Last night I used for first time my new micropc beelink bt-3 with W10 and SGP.
I had a strange problem with PHD reporting that couln't connect with the camera for 15sec and stopping the guiding, but actually the QHY5-II was working properly as I didn't watch anything strange on the guiding graphic... I changed the camera disconect timeout to 60 sec and it has work propperly during all the night, and I don't see any guiding errors on the captured lights, so I guess the 60sec stuff has worked.
The problem lies that at the end of the sequence I programmed the SGP to take 15 darks at 1x1 and another 15 at 2x2 binning.
It started to take the dark frame, finished it but while downloading image procedure gives me a camera timeout error (this happens with ATIK383L camera).
I have tried to repeat the darks when I woke up this morning, but again has give me camera timeout error.
Here are my logs:
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Looking at event[4]...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Found event event[4] with remaining frames.
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Event[4] frame count: 0/15...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Getting next event (4)...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Checking for auto manual focus (post)...
[29/07/2016 4:04:57] [DEBUG] [Main Thread] PopulateDataModel: Transferring view to the data model...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Attempting to move to next event...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Attempting to find next event...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Current event[3] frame count: 5/5...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Looking at event[4]...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Found event event[4] with remaining frames.
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Event[4] frame count: 0/15...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Getting next event (4)...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Running capture event...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] ------------- Starting capture frame for event[4] -------------
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Sending commands...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] SetFlatBox: Frame Type is Dark
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event2: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event3: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event4: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event5: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Checking for auto manual focus (pre)...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event6: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Created base name for frame capture: M102_300sec_1x1__frame1
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Created directory for frame capture: D:\m51\Dark\
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event1: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event7: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event8: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event9: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event10: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] Finished sending frame capture. Entering wait mode...
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event11: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event12: 4
[29/07/2016 4:04:57] [DEBUG] [Sequence Thread] TEMP - Current Event13: 4
[29/07/2016 4:04:57] [DEBUG] [Camera Thread] SGM_CAMERA_CAPTURE message received...
[29/07/2016 4:04:57] [DEBUG] [Camera Thread] SetAscomNormalSpeed...
[29/07/2016 4:04:57] [DEBUG] [Camera Thread] Readout speed set to NORMAL...
[29/07/2016 4:05:43] [DEBUG] [PHD2 Listener Thread] Could not process PHD2 input: "PHD will make several attempts to re-connect the camera.","Type":"warning"}" : Unexpected character encountered while parsing value: P. Path '', line 0, position 0.
[29/07/2016 4:05:46] [DEBUG] [PHD2 Listener Thread] Error: Guide star reported as lost!
[29/07/2016 4:05:46] [DEBUG] [PHD2 Listener Thread] Adding sequence level notification: Guide star lost!
[29/07/2016 4:05:46] [DEBUG] [Guider Camera Thread] Frame restart: Guide star was lost.
[29/07/2016 4:05:46] [DEBUG] [Sequence Thread] ASCOM Camera: Attempting to abort exposure...
[29/07/2016 4:05:46] [DEBUG] [Sequence Thread] ASCOM Camera: Exposure aborted...
[29/07/2016 4:05:46] [DEBUG] [Sequence Thread] ASCOM Camera: Blocking until image is aborted...
[29/07/2016 4:05:46] [DEBUG] [Camera Thread] ASCOM Camera: external abort...
[29/07/2016 4:05:46] [DEBUG] [Camera Thread] SGM_CAMERA_CAPTURE complete...
[29/07/2016 4:05:46] [DEBUG] [Sequence Thread] ASCOM Camera: Image is aborted...
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] Adding sequence level notification: Frame restart: Guide star was lost.
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] Running capture event...
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] ------------- Starting capture frame for event[4] -------------
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] Sending commands...
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] SetFlatBox: Frame Type is Dark
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event2: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event3: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event4: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event5: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] Checking for auto manual focus (pre)...
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event6: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] Created base name for frame capture: M102_300sec_1x1__frame1
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] Created directory for frame capture: D:\m51\Dark\
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event1: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event7: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event8: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event9: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event10: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] Finished sending frame capture. Entering wait mode...
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event11: 4
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event12: 4
[29/07/2016 4:05:47] [DEBUG] [Camera Thread] SGM_CAMERA_CAPTURE message received...
[29/07/2016 4:05:47] [DEBUG] [Camera Thread] ASCOM Camera: Attempting to abort exposure...
[29/07/2016 4:05:47] [DEBUG] [Camera Thread] ASCOM Camera: Exposure aborted...
[29/07/2016 4:05:47] [DEBUG] [Camera Thread] ASCOM Camera: Blocking until image is aborted...
[29/07/2016 4:05:47] [DEBUG] [Sequence Thread] TEMP - Current Event13: 4
[29/07/2016 4:10:47] [DEBUG] [Sequence Thread] TEMP - Current Event15: 4
[29/07/2016 4:10:47] [DEBUG] [Sequence Thread] Waking from exposure time sleep period...
[29/07/2016 4:10:47] [DEBUG] [Sequence Thread] Checking to see if the CCD has a temp...
[29/07/2016 4:10:47] [DEBUG] [Sequence Thread] Saving the CCD temp...
[29/07/2016 4:10:47] [DEBUG] [Sequence Thread] Entering super dangerous loop to await image completion...
[29/07/2016 4:10:47] [DEBUG] [Sequence Thread] TEMP - Current Event16: 4
[29/07/2016 4:13:47] [DEBUG] [Monitoring System Timed Message Thread] Adding sequence level notification: Failure while integrating M102; Event 5; Frame 1 for 300s. Image has not downloaded in alloted time period.
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] Adding sequence level notification: Camera timeout! No image was downloaded.
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] TEMP - Current Event17: 4
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] Image reported as complete. Continuing...
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] Collecting FITs headers...
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] ASCOM Camera: Could not get last exposure start time. Reported as (unknown)
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] DATE-LOC time provided by SGPro (failed to retrieve valid entry camera)...
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] Clearing timed monitoring events...
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] Error saving ASCOM image. : Object reference not set to an instance of an object.
at fa.a7(d A_0, List`1 A_1)
[29/07/2016 4:18:47] [DEBUG] [Sequence Thread] Save image failed!
[29/07/2016 4:19:03] [DEBUG] [Sequence Thread] TEMP - Current Event18: 4
[29/07/2016 4:19:03] [DEBUG] [Sequence Thread] TEMP - Current Event19: 4
[29/07/2016 4:19:03] [DEBUG] [Sequence Thread] Run event reported timeout...
[29/07/2016 4:19:03] [DEBUG] [Sequence Thread] Adding sequence level notification: Camera timeout! Sequence has been aborted.
[29/07/2016 4:19:10] [DEBUG] [Sequence Thread] Clearing timed monitoring events...
[29/07/2016 4:19:10] [DEBUG] [Sequence Thread] Checking RunEndOfSequenceEquipmentOptions, force = True
[29/07/2016 4:19:10] [DEBUG] [Sequence Thread] In RunEndOfSequenceEquipmentOptions
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] Stopping auto guiding...
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] Attempting to stop PHD2 guiding...
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] Checking PHD2 state...
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] PHD2 GetPhdStatus - Pre-Wait : Guiding
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] Sending to PHD2:
{"method": "get_app_state", "id": 1001}
[29/07/2016 4:19:41] [DEBUG] [TEC Thread] SGM_CHANGE_COOLER_TEMP message received...
[29/07/2016 4:19:41] [DEBUG] [TEC Thread] TEC Change: Starting...
[29/07/2016 4:19:41] [DEBUG] [TEC Thread] TEC Change: Changing temp from -10,04 to 20,00 in 300 seconds...
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] PHD2 GetPhdStatus - Post-Wait: Guiding
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] Sending to PHD2:
{"method": "stop_capture", "id": 1004}
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] Checking PHD2 state...
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] PHD2 GetPhdStatus - Pre-Wait : Guiding
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] Sending to PHD2:
{"method": "get_app_state", "id": 1001}
[29/07/2016 4:19:41] [DEBUG] [Sequence Thread] PHD2 GetPhdStatus - Post-Wait: Guiding
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] Checking PHD2 state...
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] PHD2 GetPhdStatus - Pre-Wait : Stopped
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] Sending to PHD2:
{"method": "get_app_state", "id": 1001}
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] PHD2 GetPhdStatus - Post-Wait: Stopped
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] PHD2: Successfully stopeed PHD2...
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] Autoguider (PHDv2) stopped Successfully
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] Disconnecting auto guider equipment...
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] Sending to PHD2:
{"method":"set_connected","params":[false],"id":1007}
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] Parking telescope...
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] ASCOM Telescope: Park message received.
[29/07/2016 4:19:42] [DEBUG] [Sequence Thread] ASCOM Telescope: Sending park...
[29/07/2016 4:19:59] [DEBUG] [Sequence Thread] ASCOM Telescope: Parked
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Aborting sequence timer thread...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Aborting recovery thread...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Sending sequence end notification...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Resetting UI elements...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Checking if sequence has work left...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Work left...
[29/07/2016 4:19:59] [DEBUG] [Recovery Killer Thread] Closing recovery dialog...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Updating big status...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Enabling menu items...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Set target icons...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Removing camera protection...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] Monitoring system shutdown...
[29/07/2016 4:19:59] [DEBUG] [Main Thread] SequenceEnds complete...
[29/07/2016 4:19:59] [DEBUG] [Sequence Thread] Restoring system standby state...
[29/07/2016 4:20:43] [DEBUG] [PHD2 Listener Thread] PHD2 - No messages received from PHD2 for 1 minute, checking socket with status...
[29/07/2016 4:20:43] [DEBUG] [PHD2 Listener Thread] Checking PHD2 state...
[29/07/2016 4:20:43] [DEBUG] [PHD2 Listener Thread] PHD2 GetPhdStatus - Pre-Wait : Stopped
[29/07/2016 4:20:43] [DEBUG] [PHD2 Listener Thread] Sending to PHD2:
{"method": "get_app_state", "id": 1001}
[29/07/2016 8:06:16] [DEBUG] [Sequence Thread] ********** Run sequence started **********
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Checking if observatory requires auto slaving...
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Observatory does not require auto slave...
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Attempting to find next event...
[29/07/2016 8:06:17] [DEBUG] [Main Thread] PopulateDataModel: Transferring view to the data model...
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Running capture event...
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] ------------- Starting capture frame for event[0] -------------
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Sending commands...
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] SetFlatBox: Frame Type is Dark
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event2: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event3: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event4: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event5: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Checking for auto manual focus (pre)...
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event6: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Created base name for frame capture: Target 3_300sec_2x2__frame2
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Created directory for frame capture: D:\m51\Dark\
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event1: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event7: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event8: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event9: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event10: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] Finished sending frame capture. Entering wait mode...
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event11: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event12: 0
[29/07/2016 8:06:17] [DEBUG] [Sequence Thread] TEMP - Current Event13: 0
[29/07/2016 8:11:17] [DEBUG] [Sequence Thread] TEMP - Current Event15: 0
[29/07/2016 8:11:17] [DEBUG] [Sequence Thread] Waking from exposure time sleep period...
[29/07/2016 8:11:17] [DEBUG] [Sequence Thread] Checking to see if the CCD has a temp...
[29/07/2016 8:11:17] [DEBUG] [Sequence Thread] Saving the CCD temp...
[29/07/2016 8:11:17] [DEBUG] [Sequence Thread] Entering super dangerous loop to await image completion...
[29/07/2016 8:11:17] [DEBUG] [Sequence Thread] TEMP - Current Event16: 0
[29/07/2016 8:14:17] [DEBUG] [Monitoring System Timed Message Thread] Adding sequence level notification: Failure while integrating Target 3; Event 1; Frame 2 for 300s. Image has not downloaded in alloted time period.
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] Adding sequence level notification: Camera timeout! No image was downloaded.
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] TEMP - Current Event17: 0
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] Image reported as complete. Continuing...
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] Collecting FITs headers...
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] ASCOM Camera: Could not get last exposure start time. Reported as (unknown)
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] DATE-LOC time provided by SGPro (failed to retrieve valid entry camera)...
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] Clearing timed monitoring events...
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] Error saving ASCOM image. : Object reference not set to an instance of an object.
at fa.a7(d A_0, List`1 A_1)
[29/07/2016 8:19:17] [DEBUG] [Sequence Thread] Save image failed!
[29/07/2016 8:19:33] [DEBUG] [Sequence Thread] TEMP - Current Event18: 0
[29/07/2016 8:19:33] [DEBUG] [Sequence Thread] TEMP - Current Event19: 0
[29/07/2016 8:19:33] [DEBUG] [Sequence Thread] Run event reported timeout...
[29/07/2016 8:19:33] [DEBUG] [Sequence Thread] Adding sequence level notification: Camera timeout! Sequence has been aborted.
[29/07/2016 8:19:39] [DEBUG] [Sequence Thread] Clearing timed monitoring events...
[29/07/2016 8:19:39] [DEBUG] [Sequence Thread] Checking RunEndOfSequenceEquipmentOptions, force = True
[29/07/2016 8:19:39] [DEBUG] [Sequence Thread] In RunEndOfSequenceEquipmentOptions
[29/07/2016 8:20:11] [DEBUG] [Sequence Thread] Stopping auto guiding...
[29/07/2016 8:20:11] [DEBUG] [Sequence Thread] Attempting to stop PHD2 guiding...
[29/07/2016 8:20:11] [DEBUG] [Sequence Thread] PHD2 Not connected! Attempting to reconnect.
[29/07/2016 8:20:11] [DEBUG] [Sequence Thread] Connecting to PHD2...
[29/07/2016 8:20:11] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:11] [DEBUG] [PHD2 Listener Thread] Attempting to connect to PHD2...
[29/07/2016 8:20:11] [DEBUG] [TEC Thread] SGM_CHANGE_COOLER_TEMP message received...
[29/07/2016 8:20:11] [DEBUG] [TEC Thread] TEC Change: Starting...
[29/07/2016 8:20:11] [DEBUG] [TEC Thread] TEC Change: Changing temp from -10,04 to 20,00 in 300 seconds...
[29/07/2016 8:20:12] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:12] [DEBUG] [PHD2 Listener Thread] Failed to establish client connection to PHD2 using port 4400: No connection could be made because the target machine actively refused it 127.0.0.1:4400
[29/07/2016 8:20:13] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:14] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:15] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:16] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:16] [DEBUG] [PHD2 Listener Thread] Failed to establish client connection to PHD2 using port 4400: No connection could be made because the target machine actively refused it 127.0.0.1:4400
[29/07/2016 8:20:17] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:18] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:19] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:19] [DEBUG] [PHD2 Listener Thread] Could not etablish a connection to PHD2! Aborting...
[29/07/2016 8:20:19] [DEBUG] [PHD2 Listener Thread] PHD2 connection terminated...
[29/07/2016 8:20:19] [DEBUG] [PHD2 Listener Thread] Exiting PHD2 listener...
[29/07/2016 8:20:20] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] Waiting for socket connection to PHD2...
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] Failed to connect to PHD2. Could not establish socket connection...
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] PHD2: Could not stop guider, connection check failed...
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] Autoguider (PHDv2) failed to stop!
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] Disconnecting auto guider equipment...
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] Sending to PHD2:
{"method":"set_connected","params":[false],"id":1007}
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] Parking telescope...
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] ASCOM Telescope: Park message received.
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] ASCOM Telescope: Parked
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Aborting sequence timer thread...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Sending sequence end notification...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Resetting UI elements...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Checking if sequence has work left...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Work left...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Updating big status...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Enabling menu items...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Set target icons...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Removing camera protection...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] Monitoring system shutdown...
[29/07/2016 8:20:21] [DEBUG] [Main Thread] SequenceEnds complete...
[29/07/2016 8:20:21] [DEBUG] [Sequence Thread] Restoring system standby state...
[29/07/2016 8:25:11] [DEBUG] [TEC Thread] TEC Change: Complete...
[29/07/2016 8:25:12] [DEBUG] [Main Thread] Turning camera cooler off...
[29/07/2016 8:25:13] [DEBUG] [TEC Thread] SGM_CHANGE_COOLER_TEMP complete...
[29/07/2016 8:25:13] [DEBUG] [Main Thread] Turning camera cooler off...
[29/07/2016 8:30:29] [DEBUG] [CP Update Thread] ASCOM Camera: Error in GetCoolerTemp. : Not Connected in CCDTemperature (System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.Runtime.InteropServices.COMException: Not Connected in CCDTemperature
--- End of inner exception stack trace ---
at System.RuntimeType.InvokeDispMethod(String name, BindingFlags invokeAttr, Object target, Object[] args, Boolean[] byrefModifiers, Int32 culture, String[] namedParameters)
at System.RuntimeType.InvokeMember(String name, BindingFlags bindingFlags, Binder binder, Object target, Object[] providedArgs, ParameterModifier[] modifiers, CultureInfo culture, String[] namedParams)
at System.Type.InvokeMember(String name, BindingFlags invokeAttr, Binder binder, Object target, Object[] args, CultureInfo culture)
at ASCOM.DriverAccess.MemberFactory.CallMember(Int32 memberCode, String memberName, Type[] parameterTypes, Object[] parms) in c:\ASCOM Build\Export\ASCOM.DriverAccess\MemberFactory.cs:line 243)
at ASCOM.DriverAccess.MemberFactory.CallMember(Int32 memberCode, String memberName, Type[] parameterTypes, Object[] parms) in c:\ASCOM Build\Export\ASCOM.DriverAccess\MemberFactory.cs:line 284
at ASCOM.DriverAccess.Camera.get_CCDTemperature() in c:\ASCOM Build\Export\ASCOM.DriverAccess\Camera.cs:line 128
at fa.e9()
[29/07/2016 8:30:29] [DEBUG] [CP Update Thread] ASCOM Camera: Error in GetCoolerPower. : Not Connected in CoolerPower (System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.Runtime.InteropServices.COMException: Not Connected in CoolerPower
--- End of inner exception stack trace ---
at System.RuntimeType.InvokeDispMethod(String name, BindingFlags invokeAttr, Object target, Object[] args, Boolean[] byrefModifiers, Int32 culture, String[] namedParameters)
at System.RuntimeType.InvokeMember(String name, BindingFlags bindingFlags, Binder binder, Object target, Object[] providedArgs, ParameterModifier[] modifiers, CultureInfo culture, String[] namedParams)
at System.Type.InvokeMember(String name, BindingFlags invokeAttr, Binder binder, Object target, Object[] args, CultureInfo culture)
at ASCOM.DriverAccess.MemberFactory.CallMember(Int32 memberCode, String memberName, Type[] parameterTypes, Object[] parms) in c:\ASCOM Build\Export\ASCOM.DriverAccess\MemberFactory.cs:line 243)
at ASCOM.DriverAccess.MemberFactory.CallMember(Int32 memberCode, String memberName, Type[] parameterTypes, Object[] parms) in c:\ASCOM Build\Export\ASCOM.DriverAccess\MemberFactory.cs:line 284
at ASCOM.DriverAccess.Camera.get_CoolerPower() in c:\ASCOM Build\Export\ASCOM.DriverAccess\Camera.cs:line 290
at fa.fa()