Clik here to view.
Autocenter fails after EQMOD meridian flip
PeterGoodhew: here's the link to the log file. The flip occurred at 23:07 These logs are from April 23, 2016.
View ArticleAutocenter fails after EQMOD meridian flip
Oops - yes! Try this:https://www.dropbox.com/s/uw5bijya0oceib3/sg_logfile_20161017194744.txt?dl=0
View ArticleAutocenter fails after EQMOD meridian flip
@PeterGoodhew It's hard for me to be precise with an issue like this. All I can say with any amount of confidence is that something went very wrong. Your mount is tracking and then SGPro identifies...
View ArticleRunning a Sequence
Yup. It actually has to be guiding. If you want to practice, use the simulators.
View ArticleDisable "Analyzing Star Data?"
I've read the available threads on Analyzing Star Data, and have tried to minimize its impact on my setup, but it is bogging my computer down like crazy. I've disabled Image History, but it's still...
View ArticleClik here to view.
Arduino Based Ascom Observing Conditions and Safety Monitor
Hey, Manoj: I also built an Arduino version and ASCOM driver. I left off the wind guage. I wish I had placed some tiny heat source under my raindrop detector. I have about 90 feet of nichrome wire...
View ArticleAutocenter fails after EQMOD meridian flip
Thanks Ken. As per the instructions I cleared out the model from EQMOD beforehand, sync data (DxSA and DxSB are zero)After the flip the sync corrections are active again because SGP performed a plate...
View ArticleSyncless centering successful! 2.5.2.3
Just tried this in 2.5.2.4 last night and the offset sync still requires an explicit re-setting after loading the sequence for it to work. (I am not sure from the change log if this was addressed in...
View ArticleAutocenter fails after EQMOD meridian flip
I never touch "(DxSA and DxSB)" once the telescope is in sync. In fact - I think I set them to zero once, long time ago. Still It works perfectly!
View ArticleAutocenter fails after EQMOD meridian flip
You can tell it to slew first then center the target.
View ArticleAutocenter fails after EQMOD meridian flip
FThat would be great, but I can't see any way of doing that automatically. The Meridian Flip Options panel just offers "Auto Center After Meridian Flip". Ami missing something, or does this have to be...
View ArticleDockable Modules, Can I save my layout?
Hi, Is there a way to save my setup so that next time I run SGP all the dockable modules reappear to the left and right as I set them? I seem to go back to the default modules and locations every time...
View ArticleDockable Modules, Can I save my layout?
Tom, the modules and their locations should automatically save betweensessions. What you describe is not typical behavior. The only thing I cansuggest is to uninstall and reinstall SGP to see if that...
View ArticleRun script at sequence end
Hi, I've taken automation to new levels thanks to this awesome software! This is the best software ever! In ver 2.5.1.17...In Sequence Settings, if I check Run script at sequence end and set a valid...
View ArticleDockable Modules, Can I save my layout?
Interesting, I will reinstall. I run on win7 where I see this behavior. I have another identical win7 pc that I use for post processing that this does not happen with. Thanks! I'll post my results. Tom
View ArticleDockable Modules, Can I save my layout?
Thank you! Uninstalling and re-installing resolved my issue. Thanks!Tom
View ArticleDisable "Analyzing Star Data?"
QHY9 Mono. But the camera hasn't changed. The only thing that's changed with this imaging setup in the last year is that the "Analyzing Star Data" message has become noticeable and I've kept up with...
View Article